30 mm moulded FRP grating with 13/40 mm mesh for walkway selection. Check the recorded surface and sample-specific slip report, then send your application and panel requirements.
MACHS supplied archive photograph labelled green micro. It illustrates the micro-mesh family; exact mesh, depth, resin and surface must be confirmed against the drawing and original report. It is not identification of the tested 6 #big specimen.← Moulded grating
Specification notes
Mesh
13 × 13 / 40 × 40 mm
Depth
30 mm
Tested surface
6 #big, per report
Parameter source: P01 → N016 / V9 2026-11-05 / V8 R3. Only the listed configuration is described. Missing dimensions, mass and working loads are not estimated.
Compare the geometry, not the mini-mesh label
This is the 13 × 13 / 40 × 40 mm configuration, not H30 with 19/38 mm geometry. Check the specified opening, depth and surface together. A smaller mesh alone does not prove compliance with a local access requirement.
Match the tested surface
The linked wet-pendulum report records the surface as “6 #big”. A result from that sample cannot be transferred to a smooth surface or an unconfirmed finish. Provide the project test method and required classification for review.
Prepare the enquiry
Include the panel or cut-part drawing, quantity, supports, span, expected loading, wet or chemical exposure, fixing arrangement and destination. Identify any opening or access requirement that is mandatory.
Define mesh, opening and depth separately
Use the mesh designation and panel depth as separate dimensions. Mesh pitch and the clear gap between ribs are different measurements; a smaller secondary mesh is another configuration detail. Specify the walking surface and resin independently. Ask for the applicable section drawing before matching a photograph or an abbreviated size to an order.
Decide what the application needs
For walkways, trench covers and platform areas, first identify who or what will cross the panel, support positions, clear span, load contact area and the required deflection limit. Consider drainage, debris, cleaning access and footwear when choosing an opening. A small opening or gritted surface does not by itself demonstrate compliance with a pedestrian-access or slip standard.
Agree the finished panel and fixing scope
List full-panel sizes or each cut part, finished dimensions and units, edge and cut-out locations, identification marks and fixing requirements. Distinguish panel-to-panel joining from attachment to the supporting structure. Agree which drawings, inspection criteria and records accompany the order; do not infer a tested assembly from the panel name alone.
Mini mesh and micro mesh are not interchangeable labels
This page’s mesh dimensions are the recorded configuration. Do not substitute another double-mesh arrangement merely because both products are 30 mm deep or described as mini mesh. Use the actual drawing and report sample identity, including surface preparation, when requesting slip evidence.
Swipe or scroll the table horizontally to read all columns on a small screen.
Recorded specification — 13/40 mm mesh, 30 mm moulded grating
Specification item
Recorded value
Mesh
13 × 13 / 40 × 40 mm
Depth
30 mm
Tested surface
6 #big, per report
Does a mesh size identify the whole specification?
No. Confirm mesh pitch, clear opening, depth, rib geometry, resin, surface, panel outline and supports. The same nominal mesh and depth can have different rib sections or formulations.
Technical pack for this configuration
Use the model, drawing revision and tested conditions together. Missing files are not evidence of a verified specification.
Specification: recorded parameters on this page; dimensions not listed require drawing review.
Model drawing and revision: no released model drawing is linked in this local catalogue. Request the applicable drawing.
Load / span: no general allowable-load table is released here. Confirm support, span, load direction and deflection criteria.
260811011SHF-001
13×13/40×40;30mm;湿态摆锤
13/40 mm mesh, 30 mm, 6 #big tested surface; wet pendulum AS 4586 Appendix A. P5 applies to that tested sample/surface only. Only the identified tested specimen/configuration. Matching nominal dimensions does not establish the same resin, formulation, surface, batch or working load. Confirm the proposed supply against the complete original report.
Applicant / publisher: Nantong Machs Composite Material Co., Ltd. (as recorded in original) · Source: MACHS original sample report
Version: As issued; see original · Sample report; not a product certification
Reference / method: AS 4586-2013/Amdt 1-2017 Appendix A · Issued: 2026-08-20
No blanket current certification or working-load claim. A report without an expiry date is still sample-specific.