MACHS

Moulded grating

38 × 38 × 38 mm moulded grating

38 mm-deep moulded FRP grating with 38 × 38 mm mesh for walkway and platform selection. Compare resin and surface options, then send panel sizes and support conditions for quotation.

MACHS supplied moulded grating representative product-family photograph
Representative moulded grating photograph from the MACHS supplied archive. Confirm the exact geometry, dimensions, resin and surface against the approved order drawing; the photograph is not evidence of the tested configuration.
← Moulded grating

Specification notes

ResinPolyester, isophthalic or vinyl ester — project review
SurfaceGrit, concave or smooth — specify with enquiry
Mesh38 × 38 mm
Depth38 mm

Parameter source: P004 / V9 2026-11-05 / V8 R3. Only the listed configuration is described. Missing dimensions, mass and working loads are not estimated.

Is this the configuration you need?

This entry is 38 × 38 mm mesh with a 38 mm depth. Use it as a starting point for industrial flooring, platforms or wastewater access. Confirm whether the mesh dimension on your drawing means pitch or clear opening before comparing quotations.

Choose the supply, not just the panel name

State the resin, surface, colour, panel or finished-part dimensions and quantities. A full panel and a cut part have different cutting, finishing and packing scopes. Include holes, edge treatment and fixings in the enquiry rather than assuming they are included.

Check the evidence for your configuration

Open the technical pack below to inspect the original sample reports and any customer reissues citing them. A report for a particular resin or surface is not evidence for every option on this page. For load review, send the clear span, supports, load type, contact area and allowable deflection.

Define mesh, opening and depth separately

Use the mesh designation and panel depth as separate dimensions. Mesh pitch and the clear gap between ribs are different measurements; a smaller secondary mesh is another configuration detail. Specify the walking surface and resin independently. Ask for the applicable section drawing before matching a photograph or an abbreviated size to an order.

Decide what the application needs

For walkways, trench covers and platform areas, first identify who or what will cross the panel, support positions, clear span, load contact area and the required deflection limit. Consider drainage, debris, cleaning access and footwear when choosing an opening. A small opening or gritted surface does not by itself demonstrate compliance with a pedestrian-access or slip standard.

Agree the finished panel and fixing scope

List full-panel sizes or each cut part, finished dimensions and units, edge and cut-out locations, identification marks and fixing requirements. Distinguish panel-to-panel joining from attachment to the supporting structure. Agree which drawings, inspection criteria and records accompany the order; do not infer a tested assembly from the panel name alone.

Swipe or scroll the table horizontally to read all columns on a small screen.

Recorded specification — 38 × 38 × 38 mm moulded grating
Specification itemRecorded value
ResinPolyester, isophthalic or vinyl ester — project review
SurfaceGrit, concave or smooth — specify with enquiry
Mesh38 × 38 mm
Depth38 mm
Does a mesh size identify the whole specification?

No. Confirm mesh pitch, clear opening, depth, rib geometry, resin, surface, panel outline and supports. The same nominal mesh and depth can have different rib sections or formulations.

Technical pack for this configuration

Use the model, drawing revision and tested conditions together. Missing files are not evidence of a verified specification.

SHCCM150702189

38 × 38 × 38 mm; 1220 mm span

Sample-specific load evidence; uniform load is total kN, not kN/m².

Applicant / publisher: As recorded in original report · Source: Document reference

Version: As issued; see original · Sample record — applicability review required

Reference / method: Load test · Issued: 2015-07-24

Test report: no expiry inferred. Confirm original and order applicability before use.

Read document scope and preview Download original (PDF)

101490735SAT-001B

FRP molded grating

Only the identified tested specimen/configuration. Matching nominal dimensions does not establish the same resin, formulation, surface, batch or working load. Confirm the proposed supply against the complete original report. Original sample description: FRP molded grating.

Applicant / publisher: Nantong Machs Composite Material Co., Ltd. (as recorded in original) · Source: MACHS original sample report

Version: As issued; see original · Sample report; not a product certification

Reference / method: ASTM E84-13a · Issued: 2014-01-15

No blanket current certification or working-load claim. A report without an expiry date is still sample-specific.

Read document scope and preview Download original (PDF)

210624007SHF-005

38S38; 38mm; P5; VE/ISO; sample FRP GRATING 1003

Only the identified tested specimen/configuration. Matching nominal dimensions does not establish the same resin, formulation, surface, batch or working load. Confirm the proposed supply against the complete original report. Original sample description: 38S38; 38mm; P5; VE/ISO; sample FRP GRATING 1003. P5 is part of the recorded product code here, not a slip rating.

Applicant / publisher: Nantong Machs Composite Material Co., Ltd. (as recorded in original) · Source: MACHS original sample report

Version: As issued; see original · Sample report; not a product certification

Reference / method: ASTM E84-21 · Issued: 2021-07-14

No blanket current certification or working-load claim. A report without an expiry date is still sample-specific.

Read document scope and preview Download original (PDF)

210624007SHF-006

38S38; 38mm; P5; VE/ISO; sample FRP GRATING 7035

Only the identified tested specimen/configuration. Matching nominal dimensions does not establish the same resin, formulation, surface, batch or working load. Confirm the proposed supply against the complete original report. Original sample description: 38S38; 38mm; P5; VE/ISO; sample FRP GRATING 7035. P5 is part of the recorded product code here, not a slip rating.

Applicant / publisher: Nantong Machs Composite Material Co., Ltd. (as recorded in original) · Source: MACHS original sample report

Version: As issued; see original · Sample report; not a product certification

Reference / method: ASTM E84-21 · Issued: 2021-07-14

No blanket current certification or working-load claim. A report without an expiry date is still sample-specific.

Read document scope and preview Download original (PDF)

210624007SHF-007

FRP GRATING 6001; 38s38 38/p5 Ve/iso; smooth. Inventory transcription 7035 conflicts with the original.

Only the identified tested specimen/configuration. Matching nominal dimensions does not establish the same resin, formulation, surface, batch or working load. Confirm the proposed supply against the complete original report. Original sample description: 38S38; 38mm; P5; VE/ISO; sample FRP GRATING 6001. P5 is part of the recorded product code here, not a slip rating. Product identifier is retained as printed; catalogue/summary labels differ and must not be silently harmonised. Original sample name is 6001; inventory transcription 7035 conflicts with the original and is not adopted.

Applicant / publisher: Nantong Machs Composite Material Co., Ltd. (as recorded in original) · Source: MACHS original sample report

Version: As issued; see original · Sample report; not a product certification

Reference / method: ASTM E84-21 · Issued: 2021-07-14

No blanket current certification or working-load claim. A report without an expiry date is still sample-specific.

Read document scope and preview Download original (PDF)

SDFTS25000933R01_EN

38×38×38mm FRP grating; Sample 1

Only the identified tested specimen/configuration. Matching nominal dimensions does not establish the same resin, formulation, surface, batch or working load. Confirm the proposed supply against the complete original report. Original sample description: 38×38×38mm FRP grating; Sample 1.

Applicant / publisher: Nantong Machs Composite Material Co., Ltd. (as recorded in original) · Source: MACHS original sample report

Version: As issued; see original · Sample report; not a product certification

Reference / method: ASTM E84-24 · Issued: 2025-03-06

No blanket current certification or working-load claim. A report without an expiry date is still sample-specific.

Read document scope and preview Download original (PDF)

SDFTS25000936R01_EN

38×38×38mm FRP grating; Sample 3

Only the identified tested specimen/configuration. Matching nominal dimensions does not establish the same resin, formulation, surface, batch or working load. Confirm the proposed supply against the complete original report. Original sample description: 38×38×38mm FRP grating; Sample 3.

Applicant / publisher: Nantong Machs Composite Material Co., Ltd. (as recorded in original) · Source: MACHS original sample report

Version: As issued; see original · Sample report; not a product certification

Reference / method: ASTM E84-24 · Issued: 2025-03-06

No blanket current certification or working-load claim. A report without an expiry date is still sample-specific.

Read document scope and preview Download original (PDF)

SDFTS25000938R01_EN

38×38×38mm FRP grating; Sample 4

Only the identified tested specimen/configuration. Matching nominal dimensions does not establish the same resin, formulation, surface, batch or working load. Confirm the proposed supply against the complete original report. Original sample description: 38×38×38mm FRP grating; Sample 4.

Applicant / publisher: Nantong Machs Composite Material Co., Ltd. (as recorded in original) · Source: MACHS original sample report

Version: As issued; see original · Sample report; not a product certification

Reference / method: ASTM E84-24 · Issued: 2025-03-06

No blanket current certification or working-load claim. A report without an expiry date is still sample-specific.

Read document scope and preview Download original (PDF)

SDFTS25000940R01_EN

38×38×38mm FRP grating; Sample 5

Only the identified tested specimen/configuration. Matching nominal dimensions does not establish the same resin, formulation, surface, batch or working load. Confirm the proposed supply against the complete original report. Original sample description: 38×38×38mm FRP grating; Sample 5.

Applicant / publisher: Nantong Machs Composite Material Co., Ltd. (as recorded in original) · Source: MACHS original sample report

Version: As issued; see original · Sample report; not a product certification

Reference / method: ASTM E84-24 · Issued: 2025-03-06

No blanket current certification or working-load claim. A report without an expiry date is still sample-specific.

Read document scope and preview Download original (PDF)

260717017SHF-002

38×38;38mm;1220×1220mm;申请人声明A15

CUSTOMER-HEADED REFERENCE: applicant FG Structures Ltd. Not a MACHS-held certificate. Original release requires review. Only the identified tested specimen/configuration. Matching nominal dimensions does not establish the same resin, formulation, surface, batch or working load. Confirm the proposed supply against the complete original report.

Applicant / publisher: FG Structures Ltd · Source: Customer-headed reference — not a MACHS-held certificate

Version: As issued; see original · Customer-headed latest located revision; applicability limited to tested sample

Reference / method: EN 124-1:2015 / EN 124-5:2015 · Issued: 2026-08-20

No blanket current certification or working-load claim. Client-headed original is controlled.

Original is held for release / applicability review.

190325002SHF-001

38×38mm;38mm厚;FRP molded grating

Only the identified tested specimen/configuration. Matching nominal dimensions does not establish the same resin, formulation, surface, batch or working load. Confirm the proposed supply against the complete original report. Original sample description: 38×38mm;38mm厚;FRP molded grating.

Applicant / publisher: Nantong Machs Composite Material Co., Ltd. (as recorded in original) · Source: MACHS original sample report

Version: As issued; see original · Sample report; not a product certification

Reference / method: ASTM E84-19 · Issued: 2019-04-15

No blanket current certification or working-load claim. A report without an expiry date is still sample-specific.

Read document scope and preview Download original (PDF)

Installation planning checklistRequest missing or applicable files

Compare this configuration

Installation planning · Your buying path · Technical resources

Applications

Review access around wet and corrosive process areas.Specify access around wet process areasSeparate walkway panels, removable covers and platform components; review exposure, supports and maintenance access before selecting the configuration.Specify chemical-process accessDefine the chemical exposure and the structural requirement separately, then match the proposed panel to its material evidence.Coordinate grating, framing, rails and connections.Plan industrial platforms and equipment accessCoordinate the component list, support and connection details, maintenance openings and responsibility for installation.

Capabilities

See the manufacturing behind the product.Manufacturing with a defined delivery scopeReview moulded grating, pultruded profiles and drawing-based fabrication as separate manufacturing and purchasing tasks.

Technical resources

Technical documents & report matchingFind evidence for the configuration you are considering.Your quotation checklistBring the inputs needed for a useful quotation.

FAQ

How do I choose moulded or pultruded grating?Start with clear span, support, bearing direction, load type and service conditions. Review the selection guide before choosing a configuration.Does a report cover every grating configuration?No. Match the tested sample, mesh, depth, resin, surface, colour and method to the proposed configuration. Ask for scope confirmation.Can MACHS fabricate parts to my drawing?Cutting and drilling can be reviewed against a versioned drawing. Confirm tolerances, edge finishing, inspection, labels and supply boundaries.What information is needed for distributor supply?List repeat configurations, quantities, destination, mixed loads, packing and marking. Commercial conditions are confirmed for the quotation.How is resin selected for a chemical environment?Provide chemical composition, concentration, temperature and exposure mode. Generic corrosion claims cannot establish suitability.How should I compare quotations?Use the same product configuration, fabrication, packing, documentation, freight basis and delivery conditions.

Selection guides

MACHS pultruded FRP grating panels in the workshop; representative family photograph, not a tested specimen identificationChoose moulded or pultruded gratingUse the support layout and load path to choose a starting configuration, then check the exact panel and its evidence.MACHS pultruded FRP grating panels in the workshop; representative family photograph, not a tested specimen identificationChoose resin from the actual exposureSend chemical concentration, temperature and contact conditions before asking which resin is suitable.MACHS pultruded FRP grating panels in the workshop; representative family photograph, not a tested specimen identificationCompare grating quotations on the same basisAlign the configuration, finished quantities and delivery scope before comparing the total price.MACHS pultruded FRP grating panels in the workshop; representative family photograph, not a tested specimen identificationRead a load table with its support conditionsMatch the panel, support arrangement, span and loading before using a load value.MACHS pultruded FRP grating panels in the workshop; representative family photograph, not a tested specimen identificationPrepare a repeatable distributor orderCreate a configuration-by-quantity list and agree the sample, batch, packing and documentation requirements.

Related products in this family

Review the section, dimensions and evidence for each entry. A related product is not an interchangeable or approved substitute.

MACHS supplied moulded grating representative product-family photographH30 moulded mini-mesh grating30 mm moulded mini-mesh FRP grating for walkway and platform selection. Check the recorded mesh and surface options, then send panel sizes, service conditions and quantities for review.MACHS supplied moulded grating representative product-family photograph60.2 × 76.2 S38 grating panelS38 FRP grating with 60.2 × 76.2 mm pitch for industrial access selection. Check the recorded configuration and sample evidence, then send your panel sizes and support conditions.MACHS supplied moulded grating representative product-family photograph50 × 50 × 50 mm moulded grating50 mm-deep moulded FRP grating with 50 × 50 mm mesh for platform selection. Review the sample load conditions, then send your span, loads and panel sizes for configuration review.

Request specifications

Selected product: 38 × 38 × 38 mm moulded grating. This configuration is included with your enquiry.

State known conditions and write "not sure — please advise" for anything unresolved. No need to guess the resin or load.

Privacy and enquiry data · What to include

Attach your drawing or specification and include its drawing number and revision in the requirements. You can also contact info@machsfrp.com.