Pultruded profiles
Pultruded FRP tubes
Pultruded FRP tubes for frame, rail and OEM component selection. Compare section shapes and dimensions, then send your drawing, cut lengths and quantities for supply review.

Specification notes
| Section | Round and rectangular sections |
|---|---|
| Dimensions | Submit section drawing, wall thickness and length |
| Fabrication | Cutting and drilling reviewed against drawing |
Parameter source: P018 / V9 2026-11-05 / V8 R3. Only the listed configuration is described. Missing dimensions, mass and working loads are not estimated.
Define the section
Provide the outside dimensions, wall thickness, corner details and required length. Mark critical dimensions and tolerances. A family photograph is not a dimensioned drawing, and this page does not confirm a tooling or stock size.
Separate raw lengths from finished components
Identify cuts, holes, end details and part numbers on the current drawing revision. State the assembly interface, service environment, material requirements and order or annual quantities. Agree machining and inspection scope before manufacture.
Specify the section rather than its appearance
Provide a section drawing with the dimension convention, length, tolerances and revision. For a hollow tube, identify outside dimensions and wall thickness; for a solid rod or bar, identify the diameter or solid width and thickness. For an open structural section, identify web, flange and leg dimensions separately.
Review loads, holes and connection zones
State the intended use, support and connection arrangement, load direction and any concentrated forces around holes or inserts. Pultruded composite sections require configuration-specific design review; a similar steel-section name does not establish equivalent stiffness, strength or fastening details.
Define fabrication and acceptance
Show cut lengths, hole sizes and positions, edge distances, orientation, finish and identification in the drawing package. Agree which fabrication operations and dimensional checks are included. Keep the approved drawing revision with the purchasing and inspection records so a later repeat order refers to the same configuration.
Application and assembly conditions
For a tube used in an assembly, identify its function, mating fittings and connection locations on the drawing. Distinguish a handrail member from a structural support or enclosure component. Specify outside dimensions, wall thickness, length, exposure and the project requirements; a tube photograph does not establish an approved system or electrical rating.
Swipe or scroll the table horizontally to read all columns on a small screen.
| Specification item | Recorded value |
|---|---|
| Section | Round and rectangular sections |
| Dimensions | Submit section drawing, wall thickness and length |
| Fabrication | Cutting and drilling reviewed against drawing |
Is a section photograph enough to place a repeat order?
No. Use the approved section drawing, revision, material and finish specification, length, fabrication details and acceptance criteria. A family photograph does not identify the supplied resin or dimensional tolerances.
Choose a specific catalogue section
85 source-coded geometry references. These are historical catalogue entries, not a current stock list or blanket certification. Open the exact code for dimensions, evidence limits, comparison and enquiry.
Square tube — view section codes
- ST25A FRP square tube — 25 × 25 × 3.2 × 3.2 mm
- ST25B FRP square tube — 25 × 25 × 6.4 × 6.4 mm
- ST32A FRP square tube — 32 × 32 × 3.2 × 3.2 mm
- ST32B FRP square tube — 32 × 32 × 6.4 × 6.4 mm
- ST38A FRP square tube — 38 × 38 × 3.2 × 3.2 mm
- ST38B FRP square tube — 38 × 38 × 5 × 5 mm
- ST38C FRP square tube — 38 × 38 × 6.4 × 6.4 mm
- ST44A FRP square tube — 44 × 44 × 3.2 × 3.2 mm
- ST44B FRP square tube — 44 × 44 × 6.4 × 6.4 mm
- ST50A FRP square tube — 50 × 50 × 3.2 × 3.2 mm
- ST50B FRP square tube — 50 × 50 × 3.5 × 3.5 mm
- ST50C FRP square tube — 50 × 50 × 4 × 4 mm
- ST50D FRP square tube — 50 × 50 × 5 × 5 mm
- ST50E FRP square tube — 50 × 50 × 6.4 × 6.4 mm
- ST54A FRP square tube — 54 × 54 × 3.2 × 3.2 mm
- ST54B FRP square tube — 54 × 54 × 4.8 × 4.8 mm
- ST60A FRP square tube — 60 × 60 × 5 × 5 mm
- ST64A FRP square tube — 64 × 64 × 3.2 × 3.2 mm
- ST64B FRP square tube — 64 × 64 × 4.4 × 4.4 mm
- ST64C FRP square tube — 64 × 64 × 6.4 × 6.4 mm
- ST76A FRP square tube — 76 × 76 × 3.2 × 3.2 mm
- ST76B FRP square tube — 76 × 76 × 5 × 5 mm
- ST76C FRP square tube — 76 × 76 × 6.4 × 6.4 mm
- ST76D FRP square tube — 76 × 76 × 9.5 × 9.5 mm
- ST89A FRP square tube — 89 × 89 × 6.4 × 6.4 mm
- ST90A FRP square tube — 90 × 90 × 5 × 5 mm
- ST90B FRP square tube — 90 × 90 × 6.4 × 6.4 mm
- ST100A FRP square tube — 100 × 100 × 10 × 10 mm
- ST101A FRP square tube — 101 × 101 × 3.2 × 3.2 mm
- ST101B FRP square tube — 101 × 101 × 5 × 5 mm
- ST101C FRP square tube — 101 × 101 × 6.4 × 6.4 mm
- ST101D FRP square tube — 101 × 101 × 8 × 8 mm
- ST125A FRP square tube — 125 × 125 × 6.4 × 6.4 mm
- ST125B FRP square tube — 125 × 125 × 8 × 8 mm
- ST152A FRP square tube — 152 × 152 × 6.4 × 6.4 mm
- ST152B FRP square tube — 152 × 152 × 9.5 × 9.5 mm
- ST152C FRP square tube — 152 × 152 × 12.7 × 12.7 mm
Plum-flower tube — view section codes
- CT32A FRP plum-flower tube — 19 × 32 × 6.4 mm
- CT32B FRP plum-flower tube — 25 × 32 × 3.5 mm
- CT32C FRP plum-flower tube — 22 × 32 × 5 mm
- CT34A FRP plum-flower tube — 19 × 34 × 7.5 mm
- CT37.5 FRP plum-flower tube — 37.5 × 21.5 × 8 mm
- CT42 FRP plum-flower tube — 29 × 42 × 6.4 mm
- CT45A FRP plum-flower tube — 28 × 45 × 8.5 mm
- CT45B FRP plum-flower tube — 32 × 45 × 6.4 mm
- CT51 FRP plum-flower tube — 51 × 36 × 7 mm
- CT90A FRP plum-flower tube — 71 × 90 × 9.5 mm
Circular tube — view section codes
- RT25 FRP circular tube — 25 × 3.2 mm
- RT32A FRP circular tube — 32 × 3.2 mm
- RT32B FRP circular tube — 32 × 5 mm
- RT35A FRP circular tube — 35 × 2.5 mm
- RT38A FRP circular tube — 38 × 3.2 mm
- RT38B FRP circular tube — 38 × 4 mm
- RT38C FRP circular tube — 38 × 5 mm
- RT38D FRP circular tube — 38 × 6.4 mm
- RT42A FRP circular tube — 42 × 3.2 mm
- RT42B FRP circular tube — 42 × 5 mm
- RT48 FRP circular tube — 48 × 6.4 mm
- RT50A FRP circular tube — 50 × 3.2 mm
- RT50B FRP circular tube — 50 × 4 mm
- RT50C FRP circular tube — 50 × 5 mm
- RT50D FRP circular tube — 50 × 6.4 mm
- RT60 FRP circular tube — 60 × 4.5 mm
- RT50.8 FRP circular tube — 50.8 × 6.4 mm
- RT64A FRP circular tube — 64 × 3.5 mm
- RT64B FRP circular tube — 64 × 7 mm
- RT76 FRP circular tube — 76 × 6.4 mm
- RT89A FRP circular tube — 89 × 3.2 mm
- RT89B FRP circular tube — 89 × 5 mm
- RT89C FRP circular tube — 89 × 6.4 mm
- RT99 FRP circular tube — 99 × 5 mm
- RT100 FRP circular tube — 100 × 4.5 mm
- RT101 FRP circular tube — 101 × 6.4 mm
- RT114A FRP circular tube — 114 × 3.2 mm
- RT114B FRP circular tube — 114 × 5 mm
- RT114C FRP circular tube — 114 × 6.4 mm
- RT114D FRP circular tube — 114 × 9.5 mm
- RT140 FRP circular tube — 140 × 3 mm
- RT150A FRP circular tube — 150 × 3.2 mm
- RT150B FRP circular tube — 150 × 5 mm
- RT150C FRP circular tube — 150 × 6.4 mm
- RT150D FRP circular tube — 150 × 9.5 mm
Rectangular tube — view section codes
Technical pack for this configuration
Use the model, drawing revision and tested conditions together. Missing files are not evidence of a verified specification.
- Section drawing: request the approved geometry, dimensions, tolerances and revision for the ordered section.
- Fabrication: identify lengths, holes, interfaces, material and acceptance requirements.
- Design evidence: no general section or assembly capacity is released here. Confirm supports, loads, connection details and the required test method.
No matched test report is recorded for this entry. Request a configuration-specific evidence review.
Installation planning checklistRequest missing or applicable files
Installation planning · Your buying path · Technical resources
Capabilities
Technical resources
Selection guides
Prepare a repeatable distributor orderCreate a configuration-by-quantity list and agree the sample, batch, packing and documentation requirements.
From a drawing to an agreed component supplyDefine the drawing revision, critical dimensions, machining and delivery boundary before comparing quotations.Related products in this family
Review the section, dimensions and evidence for each entry. A related product is not an interchangeable or approved substitute.
FRP rods & flat barsFRP solid rods and flat bars for fabricated components. Find a catalogue section, check its dimensions, then send your cut lengths, tolerances and quantities for quotation review.
FRP beams & structural profilesFRP beams, channels and angles for fabricated structures. Compare catalogue sections, then send your drawing, connections and design conditions to define the supply and evidence you need.
C25 FRP c-channel — 25 × 14 × 3 × 3 mmCatalogue-listed C25 FRP c-channel (25 × 14 × 3 × 3 mm). Match the dimensions to your fabrication drawing, then send cut lengths and quantities for current-supply review.Request specifications
Selected product: Pultruded FRP tubes. This configuration is included with your enquiry.
State known conditions and write "not sure — please advise" for anything unresolved. No need to guess the resin or load.

Prepare a custom-profile or OEM brief