T5020 pultruded FRP grating for walkway and platform selection. Check the catalogue geometry and separate report scope, then send your support layout, cut sizes and required surface for review.
Representative pultruded grating photograph from the MACHS supplied archive. Confirm the exact geometry, dimensions, resin and surface against the approved order drawing; the photograph is not evidence of the tested configuration.← Pultruded grating
Specification notes
Model
T5020
Depth
50 mm (report sample)
Parameter source: P02 → report 003 / V9 2026-11-05 / V8 R3. Only the listed configuration is described. Missing dimensions, mass and working loads are not estimated.
Start with the load path
Confirm the bearing-bar layout, support positions and panel direction on a drawing. The recorded 50 mm sample depth does not establish the bearing-bar spacing, panel size or allowable working load for your installation.
Read the report before naming a fire class
The linked ASTM E84 sample report identifies its own tested conditions and results. Use that complete original when reviewing a project requirement; the presence of a fire test is not a blanket fire classification for the full product family.
Define the order
Provide the resin and surface requirement, panel or finished-part size, quantity, cutouts, fixings and destination. If dimensions or performance requirements are still open, identify them explicitly for technical review.
How to specify this grating
Start with a plan showing the supporting members and the bearing bars. Pultruded bearing bars carry the principal load in their longitudinal direction; panel orientation and cut-outs must therefore be reviewed with the supports. A matching depth or model name alone does not establish interchangeable performance.
Application and supply scope
This configuration can be considered during the selection of industrial walkways, access platforms or equipment access areas. These are selection scenarios, not a claim that every installation is approved. Confirm personnel or equipment loads, wet or contaminated conditions, chemical exposure, temperature, fire requirements and the governing project specification.
Catalogue dimensions versus an approved order
The table below transcribes the supplied English catalogue, PDF 18 / printed 33; PDF 23 / printed 43. It is a catalogue reference, not an approved order drawing or confirmation of current stock. Existing V9 and original-report sample identities remain unchanged. Values not confirmed by an approved drawing must be reviewed before ordering; catalogue weight discrepancies are retained rather than silently corrected.
Surface, cutting and installation decisions
Specify the walking surface separately from the bearing-bar geometry: smooth, gritted, grooved or covered configurations require their own confirmation. State the panel outline, cut-outs, edge treatment, fixing positions, support contact and whether supply is full panels or cut parts. Neither a surface photograph nor the word anti-slip establishes a particular slip rating.
What a useful quotation should include
Provide the model or referenced section, drawing number and revision, panel or cut-part quantities, finished sizes and units, required resin and surface, support layout, loads and deflection criteria, destination and required documents. Mark undecided items for review. Confirm whether clips, fabrication, inspection records and packing are included so quotations cover the same scope.
Swipe or scroll the table horizontally to read all columns on a small screen.
Supplied catalogue reference — order review required
Item
Catalogue entry
Use condition
Catalogue designation
T-5020
Do not merge a similar profile/report code automatically
17.2 in summary; 15.66 on detail page — unresolved
Reference only; confirm configuration and revision
Source
PDF 18 / printed 33; PDF 23 / printed 43
2023 Machs English version Catalog.pdf; filename is not an approved revision date
Can I use the catalogue maximum load as the working load?
No. A maximum or ultimate load is not an allowable working load. Match the exact section and support condition, distinguish line and distributed loading, and agree the design method, load factors and deflection limit with the project engineer. Unverified catalogue load values are not a project design release.
Does the linked fire report cover every resin and surface?
No. Check the named specimen, formulation, thickness, surface and test method in the complete original. A similarly named profile, customer reissue or different resin does not automatically extend the tested scope.
Technical pack for this configuration
Use the model, drawing revision and tested conditions together. Missing files are not evidence of a verified specification.
Specification: recorded parameters on this page; dimensions not listed require drawing review.
Model drawing and revision: no released model drawing is linked in this local catalogue. Request the applicable drawing.
Load / span: no general allowable-load table is released here. Confirm support, span, load direction and deflection criteria.
260811011SHF-002
T5020;拉挤格栅;约50mm厚
T5020, approximately 50 mm sample. FSI 40 / SDI 1000; does not support a Class A claim. Only the identified tested specimen/configuration. Matching nominal dimensions does not establish the same resin, formulation, surface, batch or working load. Confirm the proposed supply against the complete original report.
Applicant / publisher: Nantong Machs Composite Material Co., Ltd. (as recorded in original) · Source: MACHS original sample report
Version: As issued; see original · Sample report; not a product certification
Historical catalogue reference; not a test report, certification, current stock statement or approved order drawing. Catalogue mass and load-table discrepancies require review.
Applicant / publisher: Publisher identified in the catalogue: MACHS · Source: Document reference
Version: Filename includes 2023; approved issue/revision date not verified · Catalogue reference — order applicability review required
Reference / method: Product reference · Issued: See original
Use current website contact details and V9 company facts. Catalogue material, load and fire claims do not replace matched original reports or project engineering.
Drawing candidate: identity confirmed; order and report applicability NOT confirmed.
T5020%20covering · b69ae766
Covering/fabrication drawing; not the bare E84 specimen
Confirmed: the drawing title, printed A0 revision and the dimensions stated above. Not confirmed: current ordered configuration or correspondence to the tested specimen. Covered/fabricated assembly is not established as the bare T5020 E84 specimen. Missing controlled section/BOM, resin/surface traceability, current model mapping and external release. Reconcile manual depth 51 mm with the report nominal 50 mm; this covering drawing is not evidence that the complete assembly was fire-tested.
Version: A0 (printed; no approved issue date recorded) · Parallel candidate — not an approved successor
Reference / method: Drawing reference — not a test report · Issued: See original
Covered/fabricated assembly is not established as the bare T5020 E84 specimen. Missing controlled section/BOM, resin/surface traceability, current model mapping and external release. Reconcile manual depth 51 mm with the report nominal 50 mm; this covering drawing is not evidence that the complete assembly was fire-tested.
Original is held for release / applicability review.