38 mm-deep moulded FRP grating with 38 × 38 mm mesh for walkway and platform selection. Compare resin and surface options, then send panel sizes and support conditions for quotation.
Representative moulded grating photograph from the MACHS supplied archive. Confirm the exact geometry, dimensions, resin and surface against the approved order drawing; the photograph is not evidence of the tested configuration.← Moulded grating
Specification notes
Resin
Polyester, isophthalic or vinyl ester — project review
Surface
Grit, concave or smooth — specify with enquiry
Mesh
38 × 38 mm
Depth
38 mm
Parameter source: P004 / V9 2026-11-05 / V8 R3. Only the listed configuration is described. Missing dimensions, mass and working loads are not estimated.
Is this the configuration you need?
This entry is 38 × 38 mm mesh with a 38 mm depth. Use it as a starting point for industrial flooring, platforms or wastewater access. Confirm whether the mesh dimension on your drawing means pitch or clear opening before comparing quotations.
Choose the supply, not just the panel name
State the resin, surface, colour, panel or finished-part dimensions and quantities. A full panel and a cut part have different cutting, finishing and packing scopes. Include holes, edge treatment and fixings in the enquiry rather than assuming they are included.
Check the evidence for your configuration
Open the technical pack below to inspect the original sample reports and any customer reissues citing them. A report for a particular resin or surface is not evidence for every option on this page. For load review, send the clear span, supports, load type, contact area and allowable deflection.
Define mesh, opening and depth separately
Use the mesh designation and panel depth as separate dimensions. Mesh pitch and the clear gap between ribs are different measurements; a smaller secondary mesh is another configuration detail. Specify the walking surface and resin independently. Ask for the applicable section drawing before matching a photograph or an abbreviated size to an order.
Decide what the application needs
For walkways, trench covers and platform areas, first identify who or what will cross the panel, support positions, clear span, load contact area and the required deflection limit. Consider drainage, debris, cleaning access and footwear when choosing an opening. A small opening or gritted surface does not by itself demonstrate compliance with a pedestrian-access or slip standard.
Agree the finished panel and fixing scope
List full-panel sizes or each cut part, finished dimensions and units, edge and cut-out locations, identification marks and fixing requirements. Distinguish panel-to-panel joining from attachment to the supporting structure. Agree which drawings, inspection criteria and records accompany the order; do not infer a tested assembly from the panel name alone.
Swipe or scroll the table horizontally to read all columns on a small screen.
Recorded specification — 38 × 38 × 38 mm moulded grating
Specification item
Recorded value
Resin
Polyester, isophthalic or vinyl ester — project review
Surface
Grit, concave or smooth — specify with enquiry
Mesh
38 × 38 mm
Depth
38 mm
Does a mesh size identify the whole specification?
No. Confirm mesh pitch, clear opening, depth, rib geometry, resin, surface, panel outline and supports. The same nominal mesh and depth can have different rib sections or formulations.
Technical pack for this configuration
Use the model, drawing revision and tested conditions together. Missing files are not evidence of a verified specification.
Specification: recorded parameters on this page; dimensions not listed require drawing review.
Model drawing and revision: no released model drawing is linked in this local catalogue. Request the applicable drawing.
Load / span: no general allowable-load table is released here. Confirm support, span, load direction and deflection criteria.
SHCCM150702189
38 × 38 × 38 mm; 1220 mm span
Sample-specific load evidence; uniform load is total kN, not kN/m².
Applicant / publisher: As recorded in original report · Source: Document reference
Version: As issued; see original · Sample record — applicability review required
Reference / method: Load test · Issued: 2015-07-24
Test report: no expiry inferred. Confirm original and order applicability before use.
Only the identified tested specimen/configuration. Matching nominal dimensions does not establish the same resin, formulation, surface, batch or working load. Confirm the proposed supply against the complete original report. Original sample description: FRP molded grating.
Applicant / publisher: Nantong Machs Composite Material Co., Ltd. (as recorded in original) · Source: MACHS original sample report
Version: As issued; see original · Sample report; not a product certification
Only the identified tested specimen/configuration. Matching nominal dimensions does not establish the same resin, formulation, surface, batch or working load. Confirm the proposed supply against the complete original report. Original sample description: 38S38; 38mm; P5; VE/ISO; sample FRP GRATING 1003. P5 is part of the recorded product code here, not a slip rating.
Applicant / publisher: Nantong Machs Composite Material Co., Ltd. (as recorded in original) · Source: MACHS original sample report
Version: As issued; see original · Sample report; not a product certification
Only the identified tested specimen/configuration. Matching nominal dimensions does not establish the same resin, formulation, surface, batch or working load. Confirm the proposed supply against the complete original report. Original sample description: 38S38; 38mm; P5; VE/ISO; sample FRP GRATING 7035. P5 is part of the recorded product code here, not a slip rating.
Applicant / publisher: Nantong Machs Composite Material Co., Ltd. (as recorded in original) · Source: MACHS original sample report
Version: As issued; see original · Sample report; not a product certification
FRP GRATING 6001; 38s38 38/p5 Ve/iso; smooth. Inventory transcription 7035 conflicts with the original.
Only the identified tested specimen/configuration. Matching nominal dimensions does not establish the same resin, formulation, surface, batch or working load. Confirm the proposed supply against the complete original report. Original sample description: 38S38; 38mm; P5; VE/ISO; sample FRP GRATING 6001. P5 is part of the recorded product code here, not a slip rating. Product identifier is retained as printed; catalogue/summary labels differ and must not be silently harmonised. Original sample name is 6001; inventory transcription 7035 conflicts with the original and is not adopted.
Applicant / publisher: Nantong Machs Composite Material Co., Ltd. (as recorded in original) · Source: MACHS original sample report
Version: As issued; see original · Sample report; not a product certification
Only the identified tested specimen/configuration. Matching nominal dimensions does not establish the same resin, formulation, surface, batch or working load. Confirm the proposed supply against the complete original report. Original sample description: 38×38×38mm FRP grating; Sample 1.
Applicant / publisher: Nantong Machs Composite Material Co., Ltd. (as recorded in original) · Source: MACHS original sample report
Version: As issued; see original · Sample report; not a product certification
Only the identified tested specimen/configuration. Matching nominal dimensions does not establish the same resin, formulation, surface, batch or working load. Confirm the proposed supply against the complete original report. Original sample description: 38×38×38mm FRP grating; Sample 3.
Applicant / publisher: Nantong Machs Composite Material Co., Ltd. (as recorded in original) · Source: MACHS original sample report
Version: As issued; see original · Sample report; not a product certification
Only the identified tested specimen/configuration. Matching nominal dimensions does not establish the same resin, formulation, surface, batch or working load. Confirm the proposed supply against the complete original report. Original sample description: 38×38×38mm FRP grating; Sample 4.
Applicant / publisher: Nantong Machs Composite Material Co., Ltd. (as recorded in original) · Source: MACHS original sample report
Version: As issued; see original · Sample report; not a product certification
Only the identified tested specimen/configuration. Matching nominal dimensions does not establish the same resin, formulation, surface, batch or working load. Confirm the proposed supply against the complete original report. Original sample description: 38×38×38mm FRP grating; Sample 5.
Applicant / publisher: Nantong Machs Composite Material Co., Ltd. (as recorded in original) · Source: MACHS original sample report
Version: As issued; see original · Sample report; not a product certification
CUSTOMER-HEADED REFERENCE: applicant FG Structures Ltd. Not a MACHS-held certificate. Original release requires review. Only the identified tested specimen/configuration. Matching nominal dimensions does not establish the same resin, formulation, surface, batch or working load. Confirm the proposed supply against the complete original report.
Applicant / publisher: FG Structures Ltd · Source: Customer-headed reference — not a MACHS-held certificate
Version: As issued; see original · Customer-headed latest located revision; applicability limited to tested sample
Reference / method: EN 124-1:2015 / EN 124-5:2015 · Issued: 2026-08-20
No blanket current certification or working-load claim. Client-headed original is controlled.
Original is held for release / applicability review.
190325002SHF-001
38×38mm;38mm厚;FRP molded grating
Only the identified tested specimen/configuration. Matching nominal dimensions does not establish the same resin, formulation, surface, batch or working load. Confirm the proposed supply against the complete original report. Original sample description: 38×38mm;38mm厚;FRP molded grating.
Applicant / publisher: Nantong Machs Composite Material Co., Ltd. (as recorded in original) · Source: MACHS original sample report
Version: As issued; see original · Sample report; not a product certification