Start with the reliability of the dimensions, rather than assume either route is cheaper. Factory fabrication needs a sufficiently settled scope to price and release. Site cutting leaves some decisions closer to the measured installation, but it also leaves fabrication work for the contractor to organise.
For a UK distributor quoting a refurbishment contractor, the commercial task is to compare the same finished requirement. An uncut panel price and a fabricated panel price describe different scopes. Put the remaining operations beside each offer before comparing totals.
Are the dimensions stable enough to release factory cutting?
Ask which dimensions have been checked against the actual installation and which remain design assumptions. A drawing can be clear and still depend on a site measurement that has not yet been taken.
Separate confirmed work from unresolved interfaces
Repeat panels with confirmed dimensions may be suitable for a factory-cut quotation. A boundary beside existing equipment may still need measurement before it can be released. Rather than force the whole order into one route, identify which components are ready and which require a later decision.
This is an enquiry method, not permission to modify a panel on site. Any proposed final adjustment still needs the applicable product and design review.
What must be included for the quotations to be comparable?
Write down the required finished output, then identify who supplies each operation. If one quote includes openings and another supplies stock panels only, the missing operations remain a project cost even when they are absent from the supplier invoice.
| Comparison item | Factory-cut offer | Site-cut offer |
|---|---|---|
| Measurements | Basis accepted for fabrication | Field measurement responsibility |
| Finished geometry | Included cuts and openings | Operations still to be performed |
| Cut-surface treatment | Agreed included scope | Required material and work allocation |
| Handling | Delivered piece sizes and packing | Stock-panel access and handling |
| Inspection | Agreed factory acceptance | Site completion checks |
| Changes | Process after fabrication release | Process before and during site work |
Ask each party to state exclusions. Do not insert assumed labour hours, waste percentages or freight savings to make an incomplete comparison look precise. Use project quotations and the contractor's actual assumptions when calculating the commercial difference.
Can the site accommodate the work left in the quotation?
Have the contractor confirm whether it can organise the remaining fabrication within the available working area and programme. Delivering larger stock panels does not establish that they can be moved to the cutting position or handled through the installation route.
Check working conditions before assigning site work
The responsible site team should plan the relevant equipment, material information and safe working arrangements. Ask it to confirm the proposed scope rather than treat site cutting as incidental assembly. This article does not provide a cutting method or prescribe exposure-control equipment.
Factory fabrication also requires planning: finished pieces must remain suitable for the agreed handling and delivery arrangement. Neither route eliminates the need to check what reaches the workface.
Who carries the cost when a dimension changes after release?
Agree the change process before ordering. Establish who can release fabrication, how a revised dimension is communicated and how the effect on already completed work will be assessed. Do not assume that a corrected drawing automatically makes a finished piece usable.
The decision should consider uncertainty as well as quoted price. A lower fabrication allowance may be outweighed by a late interface change, but that outcome needs project evidence; it should not be presented as a universal cost-saving claim.
What position does MACHS take when reviewing the fabrication scope?
MACHS offers drawing-based fabrication review. Its fabrication page describes factory cutting, openings and machining to the approved information. The product knowledge base also makes confirmation of drawings and tolerances a condition of reviewing the work. It does not make every preliminary sketch ready for production.
Gavin Yang's public comment places fabrication and installation within the overall specification decision. For a distributor, the useful implication is to quote the remaining work as carefully as the product itself. That is our editorial interpretation of his wider viewpoint, not an assertion that he recommends factory cutting for every order. View the original comment.
Next step: ask MACHS to review the fabrication enquiry with confirmed dimensions, unresolved interfaces and a list of operations you want included. Identify the moulded grating family where relevant, without treating the family name as a completed specification.
Frequently asked questions
Must the whole order use one fabrication route?
Not necessarily. Ask whether confirmed repeat components and unresolved boundary pieces can be quoted with different work allocations. Feasibility and delivery terms still need agreement.
Does factory cutting guarantee that the panel will fit an existing frame?
No guarantee follows from the fabrication location alone. The accepted measurement basis and the actual interface remain important.
Is a stock-panel quotation sufficient for a finished-cost comparison?
Only when you also account for the work and responsibilities left to other parties. Keep unpriced or uncertain items visible rather than treating them as zero.
Related buyer FAQ · Review application conditions · More buying questions
Review evidence · Discuss your requirement
Frequently asked questions
Must the whole order use one fabrication route?
Not necessarily. Ask whether confirmed repeat components and unresolved boundary pieces can be quoted with different work allocations. Feasibility and delivery terms still need agreement.
Does factory cutting guarantee that the panel will fit an existing frame?
No guarantee follows from the fabrication location alone. The accepted measurement basis and the actual interface remain important.
Is a stock-panel quotation sufficient for a finished-cost comparison?
Only when you also account for the work and responsibilities left to other parties. Keep unpriced or uncertain items visible rather than treating them as zero.
