MACHS

Pultruded profiles

FRP rods & flat bars

FRP solid rods and flat bars for fabricated components. Find a catalogue section, check its dimensions, then send your cut lengths, tolerances and quantities for quotation review.

Supplied MACHS archive photograph of solid round rods. Flat bars are a separate section option; confirm the approved drawing, dimensions, material and finish. Colours do not identify a resin or performance grade.
Supplied MACHS archive photograph of solid round rods. Flat bars are a separate section option; confirm the approved drawing, dimensions, material and finish. Colours do not identify a resin or performance grade.
← Pultruded profiles

Specification notes

SectionSolid rods and flat bars
DimensionsDiameter or section width / thickness, length and tolerances
FabricationCutting and drilling reviewed against drawing

Parameter source: P019 / V9 2026-11-05 / V8 R3. Only the listed configuration is described. Missing dimensions, mass and working loads are not estimated.

Choose the dimensions that describe a solid section

For round rods, provide diameter and length. For flat bars, provide width, thickness and length. Identify straightness, surface or dimensional tolerances that affect the assembly rather than assuming all catalogue sections have the same limits.

Define the finished part

Provide the resin or service exposure, quantity, cut lengths, holes, machining details and mating parts. Tooling availability and structural suitability are reviewed against the actual section and use, not inferred from this family entry.

Specify the section rather than its appearance

Provide a section drawing with the dimension convention, length, tolerances and revision. For a hollow tube, identify outside dimensions and wall thickness; for a solid rod or bar, identify the diameter or solid width and thickness. For an open structural section, identify web, flange and leg dimensions separately.

Review loads, holes and connection zones

State the intended use, support and connection arrangement, load direction and any concentrated forces around holes or inserts. Pultruded composite sections require configuration-specific design review; a similar steel-section name does not establish equivalent stiffness, strength or fastening details.

Define fabrication and acceptance

Show cut lengths, hole sizes and positions, edge distances, orientation, finish and identification in the drawing package. Agree which fabrication operations and dimensional checks are included. Keep the approved drawing revision with the purchasing and inspection records so a later repeat order refers to the same configuration.

Application and assembly conditions

For solid rods and flat bars used as fabricated components, identify the mating parts, cut lengths, holes and service exposure. State whether stiffness, strength, insulation or another property is required and name the test or acceptance requirement. These are part-selection inputs, not verified performance claims for every section.

Swipe or scroll the table horizontally to read all columns on a small screen.

Recorded specification — FRP rods & flat bars
Specification itemRecorded value
SectionSolid rods and flat bars
DimensionsDiameter or section width / thickness, length and tolerances
FabricationCutting and drilling reviewed against drawing
Is a section photograph enough to place a repeat order?

No. Use the approved section drawing, revision, material and finish specification, length, fabrication details and acceptance criteria. A family photograph does not identify the supplied resin or dimensional tolerances.

Files and media

Pultruded flat bars — supplied archive photograph

Supplied archive photograph of pultruded flat bars with example drilled holes

MACHS supplied archive I0537. Flat-bar family photograph only; pictured holes, sizes, colours and materials are not an approved order specification. Confirm the finished drawing and revision.

Download image (JPG)

View in technical resources

Choose a specific catalogue section

66 source-coded geometry references. These are historical catalogue entries, not a current stock list or blanket certification. Open the exact code for dimensions, evidence limits, comparison and enquiry.

Flat plank — view section codes
Flat lath — view section codes
Solid square rod — view section codes
Solid round rod — view section codes
Flat strip — view section codes
Chamfered flat strip — view section codes

Technical pack for this configuration

Use the model, drawing revision and tested conditions together. Missing files are not evidence of a verified specification.

No matched test report is recorded for this entry. Request a configuration-specific evidence review.

Installation planning checklistRequest missing or applicable files

Compare this configuration

Installation planning · Your buying path · Technical resources

Capabilities

Start with the section and its intended use.Prepare a custom-profile or OEM briefBring the section and mating-part drawings, tolerances, material requirements and quantities so tooling and the delivered component can be reviewed.

Technical resources

Section drawings, report relationships and unresolved geometryCheck catalogue section identity, held drawing candidates and the exact information still required before order or evidence release.

Selection guides

MACHS pultruded FRP grating panels in the workshop; representative family photograph, not a tested specimen identificationFrom a drawing to an agreed component supplyDefine the drawing revision, critical dimensions, machining and delivery boundary before comparing quotations.

Related products in this family

Review the section, dimensions and evidence for each entry. A related product is not an interchangeable or approved substitute.

Supplied MACHS archive photograph showing mixed pultruded section families, including I-sections and channels. Confirm the particular section drawing and dimensions; the assortment is not a claim that every size is stocked.FRP beams & structural profilesFRP beams, channels and angles for fabricated structures. Compare catalogue sections, then send your drawing, connections and design conditions to define the supply and evidence you need.MACHS c-channel family reference; not a photograph of the exact C25 sectionC25 FRP c-channel — 25 × 14 × 3 × 3 mmCatalogue-listed C25 FRP c-channel (25 × 14 × 3 × 3 mm). Match the dimensions to your fabrication drawing, then send cut lengths and quantities for current-supply review.MACHS c-channel family reference; not a photograph of the exact C26 sectionC26 FRP c-channel — 26 × 18 × 3.2 × 3.2 mmCatalogue-listed C26 FRP c-channel (26 × 18 × 3.2 × 3.2 mm). Match the dimensions to your fabrication drawing, then send cut lengths and quantities for current-supply review.

Request specifications

Selected product: FRP rods & flat bars. This configuration is included with your enquiry.

State known conditions and write "not sure — please advise" for anything unresolved. No need to guess the resin or load.

Privacy and enquiry data · What to include

Attach your drawing or specification and include its drawing number and revision in the requirements. You can also contact info@machsfrp.com.